The best projects of fences made of corrugated sheets. Project for a fence made of corrugated sheets Typical project for a fence made from corrugated sheets
Excerpt from a book
Standard gate dimensions for travel passenger car The width is 3 m, and the height is 2 m. The gate frames are welded on a flat surface, laying down boards and aligning them horizontally with a level. To get rectangular frames, you need to cut out the shelves in the corners and check the connection with a square. After this, the posts and crossbars of the gate leaves are welded, measuring and comparing the diagonals of the frame square; then the jibs are welded.
Since the steel pipe of the post has a wall thickness of 2 mm, to strengthen the fastening of the shutters, a piece of an angle with a 25 mm flange must be welded under each lower part of the cylindrical gate hinge. After this, place the sash frame on the bricks and align them horizontally and vertically, screw them to the post with soft wire, and then weld the hinges.
Fences, fences, wickets and gates on a summer cottage
Author - S.Yu. Rashchupkina
Format - pdf
Pages - 104
Size: 12 MB
Publishing house - "Eksmo"
Year of release - 2011
Excerpt from a book
In the manufacture of welded metal fences, profile pipes measuring 20x20 or 40x20 mm, a square or round rod of 10 mm, and a steel strip of 25x4 mm are most often used. Materials used for the manufacture of various fence elements various sizes, for sections it is thinner, and for pillars it is thicker.
Recently you can find it on sale ready-made fence sections. A complete fence also requires posts. The pillars can be made of metal, brick or concrete. Metal poles are usually shaped pipes 20x40, 30x40 and 50x50mm. If the fence has a base, then it must be protected from atmospheric influences with additional elements made of tin. Also, a profile pipe (usually 40x20mm) is used for transverse fence joists.
Site fencing
Author - V.I. Ryzhenko
Format - pdf
Pages - 34
Size: 59.6 MB
Publishing house - "Onyx"
Year of release - 2010
Excerpt from a book
A permanent fence is constructed from stone, brick, etc. The height of the fence must be at least 1.5 m. Cornices are built on top of brick and stone fences, which hang over the walls and are required to drain wastewater. Crowning cornices are made from the same materials as the walls.
But if you are really concerned about your own safety, then it is more appropriate to build not solid stone or brick fences, A order strong iron fences. They allow you to control what is happening outside your area.
At this point, many are faced with the problem of accurately calculating the required material. For such cases, there is a design program for the fence. With its help, you can not only visualize the future fence, but also calculate the exact amount of material.
Program interface for designing fences and fences
Manufacturing companies offer a whole range of services, including design. On the websites of such enterprises there are calculators for calculating the required material. They are very easy to use. Data on the dimensions of the future fence is entered, and an estimate is automatically generated based on them. But such programs do not design fences and are more suitable for simple fences, for example, from corrugated sheets.
But if you want everything to appear as a single whole, then it is better to turn to professionals or use a special program that will provide a number of advantages:
Having the right software will allow you to make realistic visualization and accurate calculation of the required materials.
At the moment, there are many software for highly specialized design. Several important points influence the choice of program:
Read also
Country fence repair
Some professionals use several types of software at once to create the most realistic display of a project.
Designing a fence in Excel What programs are worth paying attention to?
To design fences, you should not delve into expensive programs that will take a very long time to study; it is better to consider more simplified options for the average person.
SketchUp
Free design resource, Russified. Simple interface, large number of video lessons. The library has a wide range of elements, with the ability to add new ones. This program is more designed for the average user, therefore it does not contain the “estimate” option. Material calculation is done manually, as is cost. This helps to work with layers that display each stage of construction, including the detailing of the fence. 
3D visualization makes it possible to assess how the desired fence fits into the overall landscape design.
Our garden Crystal 10
The program is intended for the average person, but it is often used by professionals. This software allows you to design buildings and develop landscape designs. The library contains a large number of objects, including many types of fences and barriers.
Another undoubted advantage of such a program is the automatic generation of estimates for the material used in the project, and the 3D picture conveys the realism of the desired object.
To create fences in this software product, a special fence editor is used. To begin with, the planned type of structure is selected, and then the components can be replaced. Using the library's assortment, unique, individual projects are created.
Interface of the Our Garden Crystal program The generated table is output in XSL, where you can edit the received data if desired. The presence of video lessons and a simple interface make it possible to master the software in short time. Price software product from 3,000 rubles.
General instructions:
- Working drawings were developed on the basis of the approved project, in accordance with the architectural and planning assignment and technical specifications for structures and materials.
- The foundations are columnar made of monolithic reinforced concrete, connected by a grillage.
- The perimeter fence is designed in two types: brick on the side of the road and wooden between neighbors.
- The load-bearing elements are designed in the form of pillars made of monolithic reinforced concrete and brickwork.
- The brickwork is made of M 150 grade brick, reinforced every 3 rows.
- The concrete class of monolithic reinforced concrete structures is specified in the specifications for the elements.
- Longitudinal working reinforcement is adopted class A 400 (A-III), transverse – class A240 (A-I).
- The working longitudinal reinforcement is joined with an overlap. Place the joints of the rods of knitted frames and lapped meshes staggered along the length of the element. The cross-sectional area of working rods joined in one place or at a distance less than the overlap length should be no more than 50% total area sections of tensile reinforcement. The longitudinal displacement of the joint axes must be at least 1.5 times the length of the overlap. The overlap length of the working rods must be at least 40 times the diameter of the joining reinforcement.
- Bent rods are produced in a cold state on mandrels with a diameter of 3d for reinforcement class A 400 (A-III) and 2.5d for A240 (A-I).
- Construction work should be carried out in accordance with the requirements:
- earthen - SNiP 3.02.01-87;
- installation of foundations and construction of monolithic structures - SNiP 3.03.01-87
- safety precautions in construction SNiP III-4-80.
- All deviations from the fence design must be agreed upon with the developer of the working documentation.
List of working drawings:
Sheet 1: Total information
Sheet 2: Fence scheme
Sheet 3: View A
Sheet 4: View B
Sheet 5: View B. Detail D-1
Sheet 6: Fragment 1
Sheet 7: Sections 1-1 (foundation), 3-3, 4-4, 5-5, 6-6, 7-7
Sheet 8: Specification for the fence. Final bill of materials
The project was developed in accordance with the rules, regulations, instructions, and state standards.
Sheet 3 - View A
Notes:
- View A is marked on sheet 2
- Section 3-3 – on sheet 7
Sheet 4 - View B
Notes:
- See section 3-3, 4-4, 5-5, 6-6, 7-7 on sheet 7
- Part D-1 - on sheet 5
- Specification - on sheet 8
Sheet 5 – View B. Part D-1
Notes:
- See section 5-5 on sheet 7
- Fragment-1 – on sheet 6
- Specification - on sheet 8
- Install embedded parts D-1 in accordance with the technical specifications for the installation of gates and wickets.
Sheet -6 - Fragment 1. Reinforcement and formwork
Notes:
- Fragment 1 is marked on sheet 5
- Specification - on sheet 8
Sheet 7 – Sections 1-1 (foundation), 3-3, 4-4, 5-5, 6-6, 7-7
Notes:
- Sections 3-3, 4-4, 5-5, 6-6, 7-7 are marked on sheet 4
- Specification - on sheet 8
- See detail D-1 on sheet 5
Corrugated sheeting is used not only for roofing work in dachas and country houses, but also for the construction of fences and various types of enclosures.
Experience shows that installing a fence made of corrugated sheets is not difficult. However, only a professional can cope with such a task with a bang. It is important to make correct preliminary calculations without missing a single detail.
Material calculation
Construction materials for the fence:
To carry out excavation work you will need:
- Bayonet shovel. Should be level.
- Species (soviet) shovel.
It is better to entrust the marking of the fence to a professional. He will accurately calculate the need for construction and auxiliary materials, installation duration, calculate total budget construction.
What is taken into account when designing?
The design of a fence made of corrugated sheets involves preliminary development of the structure.
Sample, Click to enlarge
The place where the corrugated fence will be installed, the thickness of the structure, and the level of the foundation are selected. To do this, I install pegs at each future corner of the corrugated fence. A nylon thread is pulled between them. Using a tape measure, they take all the necessary measurements and draw up a design for a fence made of corrugated sheets. The diagram will serve as a guide for installation work in the future.
Click to enlarge
If you plan to build a narrow fence (in order to save access roads), choose.
In this case, the front side is 1.5 bricks wide, and the side is only 1 brick wide. The supporting pillar is reinforced using a profile pipe.
Pillars with embedded parts (for fastening gates and wickets) are additionally reinforced using steel pipe.
The length of the corrugated sheet for the fence is selected taking into account the height of the foundation. That is, if you want to build a fence 2 meters high, while the base will have a height of 50 cm, you need to order a profiled sheet no longer than 1.5 meters.
Foundation project
If you plan to install brick columns, a reinforced concrete strip foundation is suitable. The monolithic structure looks more solid and protects the yard from street rainwater and animals entering the site.
If the site area has significant differences, it is more rational to design a stepped foundation structure. Level differences of more than 0.5 meters will lead to significant consumption of building materials. In addition, in some places the foundation will be very high, and it will be impossible to install corrugated sheets on it.
When designing the foundation, remember that its height should not be lower than 10 centimeters above ground level. This is required so that during rain, dirt and water do not accumulate on the top of the base.
You can design a layer of different thickness - a thick foundation under the column, a narrow foundation under the profiled sheets. Thanks to this, you can also save on materials, concrete and earthworks.
Important: The instructions stipulate that the foundation is laid at a level not less than the depth of soil freezing. This will ensure reliable fastening and long service life of the entire structure. The advice concerns places with increased load (gates, wickets). In less critical places, the depth of laying the foundation in the ground can be reduced.
Metal frame project
The frame is mounted using welding. The strength of the entire structure depends on the quality of work. If the total height is more than two meters, then two rows of joists must be installed. The total estimate must include the cost of priming the frame and anti-corrosion painting.
The corrugated sheeting is attached last. The finished sheets are attached to the metal frame using self-tapping screws. Craftsmen recommend choosing fasteners to match the profile, so the fence will look monolithic.
Decoration
To decorate a fence made of corrugated sheets, materials are calculated separately. The design of gates and wickets can be created individually at the request of the customer.
Accurate calculations in materials, labor resources, etc. Only professional designers can do this. They will make an assessment directly at the site, take into account territorial features, calculate the depth of soil freezing, possible risks during operation, listen to the customer’s wishes, explain installation technology and give practical advice.
Only in this case construction estimate will be as accurate as possible, and the fence will last for decades.
Legal address: St. Petersburg,
st. Chernyakhovsky, 69 lit. B, room 1-N.
Account number 407 028 102 090 500 01913 at the branch
"Petersburg"
Saint Petersburg
c/s 301 018 101 000 000 007 490
Phone: (8
CEO
___________________
Fencing installation project
No. 3/2008 dated 01/01/2001
CEO
Chief Project Engineer
Saint Petersburg
Fencing installation project
State Healthcare Institution "City Clinic No. 000"
At the address: St. Petersburg, Vyborg district, Simonova street, building 5, building 1, letter A
No. 3/2008 dated 01/01/2001
CEO
Chief Project Engineer
Saint Petersburg
COMPOSITION OF THE PROJECT |
||
Section no. | ||
Total information Explanatory note Fencing installation diagram based on topographic survey materials of the area M 1:500 with underground communications and structures with the application of GGP and “red lines” st. Simonova. Constructive solutions for ordinary sections, gates, wickets, posts, support units. Fence installation plan based on the materials of the general plan of the site M1:500 Layout of land masses based on topographic survey materials of the site M 1:500 Electrical networks and connections plan. Construction organization project From 01/01/2001 issued |
I. GENERAL DATA
This project for installing a fence for the State Health Institution “City Clinic No. 000” at the address: St. Petersburg, Vyborgsky district, Simonova street, building 5, building 1, letter A has been developed, registration license dated January 1, 2001, issued by the Federal Agency for Construction and Housing municipal services for the design of buildings and structures of I and II levels of responsibility in accordance with the State Standard, on the basis of state contract No. 47/117 dated 01/01/01.
During the construction of the designed fence, the volumes of removed soil and construction waste will consist of waste from the following types of construction production:
1. Removal of plant soil, temporarily removed for storage in piles in a specially designated area.
2. Construction of trenches when laying and relaying underground utilities.
3. Construction waste generated during the production process construction work.
Due to the fact that at the stage of pre-project proposals there was no comprehensive data to perform the necessary calculations, the figures given below will be indicative in nature.
Calculations of volumes of transported soil
According to paragraph 1. - vegetable soil - the volume of soil is determined by the volume of the foundations being laid. Monolithic concrete block 500Х500Х1000 - 52 pcs. volume is 12.4 m3, monolithic concrete block 300x300x1000 - 40 pcs. volume is 10 m3. The total volume of concrete foundations and excavation is 22.4 m3.
Volume of removed and retained soil layer for lawn installation =
16.6 m2 x 0.1 m = 1.66 m3
Soil weight = 1.66 m3 x 1.8 t/m3 = 2.99 t.
Upon completion of construction work construction garbage will be placed at a specialized licensed testing site.
Waste generated during the operation of the facility:
During the operation of the fence, no waste is generated.
conclusions
Waste removal will be carried out under contracts with specialized enterprises for waste disposal and disposal. The frequency of waste removal is determined by the degree of its toxicity, maximum accumulation standards, sanitary and hygienic rules and safety regulations. The place where waste is accumulated must exclude the possibility of contact with the natural environment.
Disposal of consumer waste in a place protected from the influence of precipitation, eliminating the possibility of contamination of soil, ground and surface waters. There is no impact on the environment during the implementation of this project.
X APPS
Technical task
for the development and approval of a fencing installation project
building of St. Petersburg State Healthcare Institution “City Clinic No. 000”
at the address: st. Simonova, 5, bldg. 1, letter A
Basis for design | Targeted program of St. Petersburg State Healthcare Institution "City Clinic" |
|
Customer | St. Petersburg State Healthcare Institution "City Clinic No. 000" |
|
Staged design | Design and survey work |
|
Type of construction | New construction |
|
General design organization | ||
Composition of the work performed. | Development of a project for installing a fence around the area around the building of the State Healthcare Institution “City Clinic No. 000”, located at the address: st. Simonova, bldg. 1, lit. A |
|
Requirements for design documentation | The project should be developed within the boundaries indicated on the attached diagram M 1:2000, issued on February 22, 2008, No. /5 by the Committee on Urban Planning and Architecture of St. Petersburg; Develop the project in accordance with current norms and regulations; Perform landscaping adjustments based on topographic materials M 1:500, with underground communications and structures with the application of GGP and “red lines” of the street. Simonov, indicating the installation line of the fence along the border of the site; The project as a whole should be submitted for approval to the Interdepartmental Commission of the Vyborg District Administration; |
|
Special conditions | The customer provides the source materials: Technical passport of the building; Notarized copies (three) of title documents for a building, land plot; Available technical documentation for the proposed fencing. |
|
Amount transmitted to the customer of the design documentation. | The developed design documentation is provided to the Customer in 2 (two) copies in paper form + 1 copy in electronic form. |
SIGNATURES OF THE PARTIES
